background image

6

7

Transportation of a case that has been packed into a packing case

Platform for transporting

3.After moving the front glass forward put it, along with the guide, into 
   the bottom hinge (dwg 3).
4.Lay the front glass leaning it against the lamp enclosure.
5.Protect the lamp's cable using a protection cap (dwg 4)

               dwg 4                                        dwg 3 

For cabinets with straight windows:

1.Put side windows into the guides (dwg 1), install the lamp housing 
   and screw in holding down bolts (dwg 2).
2.Install couplers for side windows (dwg 2).
3.Install the front window in the same way like the curved window.
4.Screw in M6 bolts fixing the front window (dwg 2).
5.Protect the lamp's cable using a protection cap (dwg 4).
6.Install the upper shelf and screw in fixing bolts (dwg 2).

                             III. Assembly

A.Unpack the cabinet and remove protective elements

B. Wash the whole cabinet with water at the water temperature not 

0

     exc40  C and with addition of a washing liquid.
C. If a customer receives the cabinet that is partially disassembled then, 
     to protect it while transporting, the following steps should be taken:

For cabinets with curved front windows:

1. Put side windows into the guides (dwg 1)

2. Install lamps' housings and screw
    in clamping screws (dwg 2).

dwg 2                                                    dwg 1

                                              Location

1. The unit should be located in a dry place, not exposed to the sunlight. 
    Such a place should ensure good change of air (the gap between the 
    cabinet and wall must be at least 10 cm) and should be away from heat 
    sources as well as from devices forcing the airflow like ceiling fans 
    and portable heat blowers.

2. The cabinet should be placed on the even and stable base and then 
    levelled (by screwing in or unscrewing legs if necessary) (dwg 5).

www.horepa.nl

Tel: +31 226 354535

Summary of Contents for TATIANA 1.0 T







Reviews: