background image

 

REFRIGERATION LTD 

 

14 

www.igloorefrigeration.com

 | 

Ice Cream/ Gelato

 

 

•    Light switch is turned on. 
•    Lamp or starting switch of the unit is not burnt. 
 

Water leakage from under the device: 

•    Check whether the equipment is properly levelled. 
•    Empty the condensate container. 
 

The equipment does not reach the proper temperature, the light is on... – Make sure that: 

•    The main switch is on. 
•    Temperature setting on the thermostat is properly set. 
•    Thermostat works properly. 
•    The condenser is clean, if necessary – clean the condenser. 
•    Ambient temperature does not exceed 25ºC. 
•    Enough time has passed for products to be cooled. 
•    Ventilation holes are not blocked. 

 
The equipment is working too loud...– Make sure that: 

•    The equipment is standing stably and is properly levelled. 
•    Furniture adjoining the equipment does not vibrate when self-contained compressor is working. 
 

A noise made by the operating device is normal. The units are equipped with 
ventilators, engines and compressors, which turn on and off automatically. Each 
compressor makes certain noises when operating. These sounds are made by the 
aggregate engine and by cooling agent flowing through the circuit. This 
phenomenon constitutes a technical feature of cooling devices and does not signify 
equipment failure. 

 

Steam precipitation on the glass is normal in the event of high relative air humidity 
exceeding 55% and does not require calling for service 

6.2 Service 

IGLOO Refrigeration service  

Telephone number:

 416-663-3051 or (toll free) 1-888-408-8819   

E-mail:

 [email protected] 

If after checking points described in chapter 6.1 “Faults identification and repair” the unit still does not work 
properly,  

Please contact Technical Service @ IGLOO Refrigeration. 

Summary of Contents for ARB2F Series















Reviews: