background image

 

 

Page | 42 
 

5.3.1 

 Battery Maintenance 

 

 

In the case of TB trailers the battery is 
carried underneath the body inside the 
vee of the drawbar and access requires 
that the body be tilted. Do not attempt 
to inspect or charge the battery unless 
the tilted body is safely supported 

 not 

just held up by the hydraulic ram. 
 

 

The battery needs charging when the light 
on top shows red. A green light indicates 
that the battery is adequately charged. 

Always use a “smart” charger.

 

 

 

So-

called “smart” chargers are available which are 

supposed to prevent overcharging 

damage*. However the most reliable method is to monitor the open-circuit voltage (charger 
disconnected, everything off). At 12.2V the battery is half charged. Above this voltage there is 
plenty of capacity left and the risk of overcharging is best avoided. Below this voltage charging 
in-the green up to the fully charged 12.7V requires careful monitoring. 

 

 

Match charger to battery type and capacity. 

 

 

Ensure charging take place in a well-ventilated area where there is no risk of sparks of flame. 
Charging produces small quantities of highly flammable hydrogen gas. 

 

 

Ensure that the charger leads are connected to the correct battery terminals: positive to 
positive, and negative to negative BEFORE SWITCHING ON THE CHARGER. 

 

 

Once charging is complete SWITCH OFF THE CHARGER BEFORE DISCONNECTING ITS LEADS TO 
THE BATTERY. 

 

 

If the battery becomes hot or acid leaks out, then stop charging immediately. At this point the 
battery is almost certainly damaged and dangerous and should be replaced. 

  

 

Do not charge a frozen battery, or a battery with a temperature above 45

°

C. 

 

 

The battery will self-discharge slowly even when unused. Allowing the battery to fall into deep 
discharge** will make recovery slow or impossible. A voltage check and appropriate recharge 
every 6 months is essential. 

 

 

In very cold weather internal freezing is a risk. Should this happen the battery may split and 
leak. Keeping the battery fully charged greatly reduces the risk of freezing damage. 
 

 

Rapid charging should be avoided if at all possible because it will result in up to 30% reduction 
in the number of charge cycles the battery will accept. 

 

Summary of Contents for CT166
























































Reviews: