IFM SDG070 Operating Instructions Manual Download Page 21

Page: 21 / 21

►

Press [Set] briefly�

> The unit displays the corresponding parameter value� After about 15 s it again

displays the parameter, then it returns to the Run mode�

11.2 Changing the display unit in the Run mode

►

Press [Set] briefly in the Run mode� Press the pushbutton to move to the next

display unit�

> The unit displays the current measured value for approx� 15 s, the correspond-

ing LED lights�

11.3 Error indications

[SC1]

Short circuit in OUT1�*

[SC2]

Short circuit in OUT2�*

[SC]

Short circuit in both outputs�*

[OL]

Measured value > 120 % of the final value of the measuring range�

[Err]

Flashing: error in the measuring probe�

*The output concerned is switched off as long as the short circuit exists�

These messages are displayed even if the display is switched off�

11.4 General operating conditions

• From time to time check the measuring probes visually for build-up�

Removal of the sensor: Loosen the coupling nut, remove the sensor from the

measuring hole (figure in

→ 6.5

)� Installation

→ 6.5

�

• If necessary, clean them at regular intervals� To do so, use a suitable cleaning

liquid (e�g� alcoholic solution)�

• Avoid mechanical damage to the measuring probes�

12 Technical data and scale drawing

Technical data and scale drawing at www�ifm�com�

Summary of Contents for SDG070






















Search results

Summary of Contents for SDG070

Reviews:

Brands by name

Popular brands

IFM SDG070, Operating Instructions Manual

Search results

Summary of Contents for SDG070

Reviews:

Brands by name

Popular brands