background image

CR3156

mobileIoT gateway

8

Object

Index

Subindex

Type

Default

Description

Analogue input 3

0x546F

0x16

R32
ro

Pin 6 of the 14-pin Micro Timer II connector

Raw value of the analogue input measure-
ment (Volt)

No filtering applied

IO – clamp 30
voltage

0x3333

0x67

R32
ro

Terminal 30

Raw value of the analogue input measure-
ment (Volt)

IO – clamp 15
voltage

0x3333

0x66

R32
ro

Terminal 15

Raw value of the analogue input measure-
ment (Volt)

IO – clamp 15
(ignition) state

0x3333

0x01

U8
ro

Terminal 15

0 = input signal low (< 2.5 V)

1 = input signal high (> 5.5 V)

IO = digital out-
put

0x3333

0x0F

U8
rw

Pin 7 of the 14-pin Micro Timer II connector

Bit 0: (0 = output signal low, 1 = output sig-
nal high)

Bits 1...7: reserved, set to 0

IO – digital out-
put status

0x3333

0x10

U8 
ro

Pin 7 of the 14-pin Micro Timer II connector

Bit 0: (0 = output signal error, 1 = output sig-
nal OK)

Bits 1...7: reserved, set to 0

IO – device tem-
perature

0x3333

0x0E

S16
ro

Device temperature in °C

The unit can send this data via the CAN interface. The configuration is made via the following objects:

Object

Index

Subindex

Type

Default

Description

DeviceMode

0x4001

0x02

U8
rw

Bit 0: compatibility mode with unit CR3114
(1 s cycle)

Bit 1: forward device status via CAN bus (1 s
cycle)

Bit 2: forward complete GNSS data via CAN
bus (1 s cycle)

Bit 3: forward input/output data via CAN
bus (1 s cycle)

Bit 4: forward acceleration and gyroscope
data via CAN bus (100 ms cycle)

IO BaseID

0x4005

0x07

U16

0x400

COB ID start address for input/output data
transmission (1s cycle)

The exact index and subindex can be found in the corresponding EDS file.

All data available in the respective device mode are sent via the CAN1 interface.

The data of the input/output functions are mapped to the following CAN messages:

COB ID

Start byte

Length
(bytes)

Type

Object

IO 0x00

0

4

R32

IO – clamp 30 voltage

4

4

R32

IO – clamp 15 voltage

IO 0x01

0

4

R32

Analogue input 1

4

2

S32

IO – device temperature

Summary of Contents for mobileIoT CR3156

























Reviews: