IFM FX460 Operating Instructions Manual Download Page 35

Page: 35 / 47

Operating instructions FX460

9.10 Preselection 2 Menu

SOURCE 2

Source for preselection 2

(→ 9.9 Preselection 1 Menu)

MODE 2

Switching condition for preselection 2, see Preselection 1 Menu (except tracking preset)
See Preselection 1 Menu

RES≥PRES-TRAIL

Tracking preset 2:

Display value greater than or equal to preselection 1 – preselection 2

Preselection 2 is the tracking preset of preselection 1�

HYSTERESIS 2

Switching hysteresis for the switching condition of preselection 1, see Preselection 1 Menu

PULSE TIME 2 (S)

Duration of the fleeting pulse for the switching condition of preselection 2, see Preselection 1 Menu

OUTPUT TARGET 2

Assignment of an output for the switching condition of preselection 2, see Preselection 1 Menu

OUTPUT POLARITY 2

Switching status for the switching condition of preselection 2, see Preselection 1 Menu

OUTPUT LOCK 2

Latching for the switching condition of preselection 2, see Preselection 1 Menu

START UP DELAY 2 (S)

Start-up delay for the switching condition of preselection 2, see Preselection 1 Menu
(Start-up delays 3 and 4 are set automatically�)

EVENT COLOR 2

Event-dependent colour change of the display for the switching condition of preselection 2, see

Preselection 1 Menu

9.11 Preselection 3 Menu

SOURCE 3

Source for preselection 3

(→ 9.9 Preselection 1 Menu)

MODE 3

Switching condition for preselection 3, see Preselection 1 Menu (except tracking preset)
See Preselection 1 Menu

RES≥PRES-TRAIL

Tracking preset 3:

Display value greater or equal to preselection 4 – preselection 3

Preselection 3 is the tracking preset of preselection 4�

HYSTERESIS 3

Switching hysteresis for the switching condition of preselection 3, see Preselection 1 Menu

PULSE TIME 3 (S)

Duration of the fleeting pulse for the switching condition of preselection 3, see Preselection 1 Menu

Summary of Contents for FX460
















































Search results

Summary of Contents for FX460

Reviews:

Related manuals for FX460

Brands by name

Popular brands

IFM FX460, Operating Instructions Manual

Search results

Summary of Contents for FX460

Reviews:

Related manuals for FX460

Brands by name

Popular brands