IFM DP2122 Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 33

background image

DP2122

Speed monitor

18

8 Menu

If a scaling is set, the menu settings of all frequency and speed dependent parameters (SP,
cFH, etc.) are also scaled.

8.1 General

Irrespective of the operating mode (standard IO mode or IO-Link device) there are two options to set
the parameters of the unit:

•

directly on the unit via the menu Parameter setting (

•

or via an IO-Link tool

Access via an IO-Link tool has a higher priority than parameter setting via the menu.

Parameter cloning and parameter setting backup is possible with an IO-Link tool.

Some parameters can only be set via the IO-Link interface:
Parameters adjustable via IO-Link (

If the unit was locked via IO-link, it can also only be unlocked via the IO-Link interface:
Locking / unlocking (

«
...
16
17
18
19
20
...
»

Summary of Contents for DP2122


































Reviews:

No comments

Related manuals for DP2122

S243HL - Bmii Widescreen Slim WLED Display

Brand: Acer Pages: 2

Brand: Barco Pages: 4

Brand: Barco Pages: 2

Brand: Daewoo Pages: 19

Brand: Daewoo Pages: 12

Brand: Daewoo Pages: 36

Brand: Daewoo Pages: 70

Brand: Zenith Pages: 32

Brand: Levita Pages: 28

COST CONTROL 3362

Brand: La Crosse Technology Pages: 18

Brand: Marshall Electronics Pages: 2

Brand: TracMap Pages: 36

Brand: FDS Pages: 25

Brand: Well Health Pages: 156

Brand: AOC Pages: 52

ProcessViewDisplay ME61

Brand: Burkert Pages: 24

FP547 - 15" LCD Monitor

Brand: BenQ Pages: 43

Brand: Sanitas Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands