IFM Electronic OPD100 Operating Instructions Manual Download | Manualshive

Page: 11 / 39

background image

11

UK

4.1.2 Operation with IO-Link master

If the sensor is connected to an IO-Link master, parametter setting, triggering

and data recording can be done completely via IO-Link� The cyclic process data

include the matching value and the switching information (good part / bad part)�
Additional functions are available via IO-Link:

-detection of the number of trigger processes
-device identification

More information → www.ifm.com → Data sheet.

4.1.3 Operation with the Vision Assistant parameter setting software and an

IO-Link master

Via the IO-Link protocol, high-resolution profile images are continually transmitted�

The image data of a profile image is split up into several data packages and

transmitted in a sequence of IO-Link data frames�
The ifm software package Vision Assistant includes a corresponding protocol

handler that combines the profile images and visualises them�
This simplifies the teaching process (guided teach), as the detection zone of the

sensor and the assessment of the profiles is visualised base on the profile images�
Prerequisite:

-IO-Link master
-ifm parameter setting software "ifm Vision Assistant" (E3D300)

Additional functions are available with the Vision Assistant software package:

-Overlay of the ROI in high-resolution profile images for a very precise setting�
-Extensive status information, useful in difficult measurement situations�

Visualisation of profiles can also be done using a customer-specific

software� The information required for this can be found in the IODD�

More information → www.ifm.com → Vision Assistant.

«
...
9
10
11
12
13
...
»

Summary of Contents for OPD100








































Reviews:

No comments

Related manuals for OPD100

Brand: Makita Pages: 64

Brand: AAT Pages: 6

Brand: AAMP of America Pages: 6

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: PASCO Pages: 5

Brand: PASCO Pages: 4

Brand: PASCO Pages: 8

Brand: PASCO Pages: 4

Brand: PASCO Pages: 12

Brand: PASCO Pages: 5

Brand: PASCO Pages: 3

Brand: Xerox Pages: 10

Brand: aci Pages: 4

HIGH BAY Series

Brand: RAB Pages: 2

Brand: Snapper Pages: 1

Brand: Whispbar Pages: 16

Brand: Valor Fires Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands