IFM Electronic efector300 SU9004 Operating Instructions Manual Download Page 22

Page: 22 / 23

11.4 Fault indications

[SC1]

Short circuit in OUT1�

[SC2]

Short circuit in OUT2�

[SC]

Short circuit in both outputs�

[OL]

Detection zone of volumetric flow or temperature exceeded�

Measured value between 120 % and 130 % of the final value of the measuring

range�

[UL]

Below the temperature detection zone: measured value below -10°C (14 °F)�

[Err]

•

Unit faulty / malfunction�

•

Measured value greater than 130 % of the final value of the measuring range�

[SEnS] Sensor indicates incorrect measurement� Possible cause: accumulated gas and

air in the medium or unit�

For more detailed diagnostics / fault assessment:

►

Briefly press [Set]�

> The latest measured values are displayed�

[IOE]

Flow sensor faulty

[Loc]

Setting pushbuttons locked, parameter change rejected�

12 Technical data

Technical data and scale drawing at www�ifm�com�

Summary of Contents for efector300 SU9004
























Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands

IFM Electronic efector300 SU9004, Operating Instructions Manual

Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands