IFM Electronic efector300 SU9004 Operating Instructions Manual Download Page 21

Page: 21 / 23

11 Operation

11.1 Read the process value

The LEDs 1-6 signal which process value is currently displayed�
The process value to be displayed as standard (temperature or volumetric flow)

can be preset → 10.4.3 Configuration of the standard display).

A standard unit of measurement can be defined for the flow velocity and the tem-

perature (→ 10.4.1 and → 10.4.2).

11.2 Change the display unit in the Run mode

►

Briefly press [Set] in the Run mode� Press the button to move to the next dis-

play unit� The display changes according to the preset:

l/min – m

/h – °C/°F

gpm – gph – °C/°F

> The unit displays the current process value in the selected display unit for ap-

prox� 15 s, the corresponding LED is lit�

11.3 Read the set parameters

►

Briefly press [Mode/Enter] to scroll the parameters�

►

Briefly press [Set] when the requested parameter is displayed�

> The unit displays the corresponding parameter value� After about 15 s it again

displays the parameter, then it returns to the Run mode�

Summary of Contents for efector300 SU9004
























Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands

IFM Electronic efector300 SU9004, Operating Instructions Manual

Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands