manualshive.com logo in svg

IFM Electronic efector300 SI5010, Operating Instructions Manual, Page: 8 / 14

Share
Download
IFM Electronic efector300 SI5010 Operating Instructions Manual Download Page 8

8

6  Operating and display elements

         

1: Operation indication

• The green LEDs indicate the current flow (LEDs 0 to 9 represent the range between flow 

standstill and maximum flow)�

• A lighting LED indicates the position of the switch point  (orange = output closed, red = 

output open)�

2, 3: Setting buttons for adjustment and configuration

7  Parameter setting

Parameters can be set before installation and set-up of the unit or during opera-

tion�

If you change parameters during operation, this will influence the function� 

 

► Ensure that there will be no malfunctions in your plant�

7.1  IO-Link
7.1.1  General information

This unit has an IO-Link communication interface which requires an IO-Link-capa-

ble module (IO-Link master) for operation�
The IO-Link interface enables direct access to the process and diagnostic data 

and provides the possibility to set the parameters of the unit during operation�
In addition communication is possible via a point-to-point connection with a USB 

adapter cable�
You will find more detailed information about IO-Link at www�ifm�com/gb/io-link�

Summary of Contents for efector300 SI5010















Reviews:

No comments