IFB AW60-806, Operation Manual

Page: 9 / 14

TROUBLE SHOOTING
Exceptional
phenomenon
Cause Solution
No indication
in controller
The power plug is not plugged tight.
The power switch is not switched
on.
Not press "START/PAUSE" button.
Power cut.
Re-plug the power plug.
Check the power socket, or change other
socket.
Press "START/PAUSE" button.
Wait for switching on electricity.
The inlet hose
.leakage
Do not rightly connect the tap with
the universal connector.
Do not screw tight the nut of the
water inlet hose.
Re-install rightly the universal connector.
Screw tight the nut.
Does not drain
The drain hose is wrung or jammed.
Loosen the drain hose for smooth flow
of water
Dose not inject water
Stop water.
Do not open the tap.
Whether the wire netting in the water
inlet was stopped up by the sundries.
Wait for coming water.
Open the tap.
Clean the netting according to the method of
"Cleaning of the water inlet".
Spinning stops and
water injecting begains
in the course of spin
Cause by that the washing
This is automatic rectification for spinning
in the washing program. That the washing
are too much or too little, or that the
washing machine is not placed plane will
cause the unbalance in time of spinning. If
there is still abnormal circumstances after
checking the above-mentioned points,
please pull out the power plug and contact
with local service as soon as possible.
Does not spin
After end to drain, do not close the lid.
Open the lid in course of spinning.
Close the upper lid.
Intermittent spinning
In order to attain the better
spinning effect.
Belong to the normal
phenomenon generally.
Before using the machine
water exists in the drain
hose.
Remainning water due to testing
or experiment in the factory.
Belong to the normal
phenomenon generally.
Notices:
The washing machine does not work normally because the voltage is low or too high. Please pull
out the plug and wait till the voltage becomes normal.
If there is still abnormal circumstances after checking the above-mentioned points, please pull out
the plug. Do not repair it by yourself at home, which is very dangerous.
METHOD OF MAINTENANCE
The following cases are not faults
1.There is water injection in time of washing or rinse, which is due to that the washer senses the
inadequacy of water and exchanges water level automatically.
2.There is the phenomenon of intermittent spinning in the beginning of spinning, which is performed
to achieve better spinning effects.
3. In the course of spin, the program return to the wash program. Because that is designed to rectify
the unbalanced distribution of load in the spin tub.
Method Of Maintenance
After the whole washing program
Maintenance of shell
The washing machine will send off the "DOU-
DOU"sound after any program operation to
remind you of taking out the load or going on
with other operations.
After finishing washing, please shut off the tap,
pull out the plug in case of water leakage or fire
Use soft cloth to wipe off the
water and dirt on the surface
each time after use of the
washing machine. Detergent,
propellant and other chemicals
are not allowed to use, for they
can cause damage to the
surface.
Cleaning the water inlet
After long time use, the water inlet mesh bag may
be blocked with smudginess, and should be
cleaned according to the following steps:
1. Switch on the power, followed by shutting off the
tap .
2. Let the washer works for 5 seconds so that water
flows into the tub through the water inlet hose. then
turn off the power.
3. Unload the water inlet hose and clean the mesh
bag, then restore the water inlet assembly.
Cleaning of the lint filter
A f t e r u s i n g t h e
washing machine for a
period, please clean
according the following
steps:
1. Take out the lint filter.
2. Turn the mesh bag
outside and wash it
clean in the water.
3. Restore it and refix it.
Clasper
Slot
15
16