ãäå êîýôôèöèåíò çàïàñà (1,25).
– ðàçú¸ì «
G
» êîíòðîëëåðà – çåë¸íûé;
Âûáîð áëîêà ïèòàíèÿ ïðîèçâîäèòü ïî ñëåäóþùèì ïàðàìåòðàì:
Ñõåìà ïîäêëþ÷åíèÿ îäíîöâåòíîé ñâåòîäèîäíîé ëåíòû ê áëîêó ïèòàíèÿ ïîêàçàíà íà
ðèñóíêå 3. Ìàêñèìàëüíîå óäàëåíèå ñâåòîäèîäíîé ëåíòû îò áëîêà ïèòàíèÿ áåç ïîòåðè
îñâåù¸ííîñòè íå áîëåå 7 ìåòðîâ.
– âûõîäíîå íàïðÿæåíèå áëîêà ïèòàíèÿ (12 Â);
– ìîùíîñòü áëîêà ïèòàíèÿ, (Âò);
– ñòåïåíü çàùèòû îò âëàãè, (
IP
).
Ïîäêëþ÷åíèå ïîëíîöâåòíîé
RGB
ñâåòîäèîäíîé ëåíòû ïðîèçâîäèòü ÷åðåç
ñïåöèàëüíûé
RGB
êîíòðîëëåð ñîãëàñíî ìàðêèðîâêå:
2)ðàçúåì «
N
» - íåéòðàëüíûé ïðîâîäíèê ñåòè;
Ïîäêëþ÷åíèå ïîëíîöâåòíîé
RGB
ñâåòîäèîäíîé ëåíòû è ìóëüòèáåëîé ëåíòû
ïðîèçâîäèòü ÷åðåç ñïåöèàëüíûé êîíòðîëëåð è áëîê ïèòàíèÿ, íîìèíàëüíàÿ ìîùíîñòü
êîòîðûõ äîëæíà ñîîòâåòñòâîâàòü ñóììàðíîé ìîùíîñòè ïîäêëþ÷àåìûõ ê íèì ëåíò.
– ïðè íåîáõîäèìîñòè ïîäêëþ÷èòü îòäåëüíûì ïðîâîäîì äîïîëíèòåëüíóþ ëåíòó
ïàðàëëåëüíî ê áëîêó ïèòàíèÿ. Ñóììàðíàÿ ìîùíîñòü ïîäêëþ÷àåìûõ ëåíò íå äîëæíà
ïðåâûøàòü ìîùíîñòü áëîêà ïèòàíèÿ.
– ðàçú¸ì «
V
+» êîíòðîëëåðà - ïëþñîâîé ðàçúåì.
Ñõåìà ïîäêëþ÷åíèÿ ïîëíîöâåòíîé
RGB
ñâåòîäèîäíîé ëåíòû ê áëîêó ïèòàíèÿ è
êîíòðîëëåðó ïîêàçàíà íà ðèñóíêå 4.
Íåîáõîäèìóþ ìîùíîñòü áëîêà ïèòàíèÿ ðàññ÷èòàéòå ïî ôîðìóëå:
1)ðàçúåì «
L
» - ôàçíûé ïðîâîäíèê ñåòè;
– ðàçú¸ì «R» êîíòðîëëåðà – êðàñíûé;
– ðàçú¸ì «
B
» êîíòðîëëåðà – ñèíèé;
Ìîùíîñòü áëîêà ïèòàíèÿ (Âò)= ñóììàðíàÿ äëèíà ëåíòû (ì)* ìîùíîñòü
ñâåòîäèîäíîé ëåíòû (Âò/ì)* êîýôôèöèåíò çàïàñà,
îáðàçîì:
– ïîäêëþ÷èòü ñâåòîäèîäíóþ ëåíòó ê êîíòàêòàì áëîêà ïèòàíèÿ ñîãëàñíî ïîëÿðíîñòè:
1)êðàñíûé ïðîâîäíèê ëåíòû (ïëþñ) - ê çàæèìó «
V
+» áëîêà ïèòàíèÿ;
2) ÷¸ðíûé ïðîâîäíèê ëåíòû (ìèíóñ) - ê çàæèìó «
V
-» áëîêà ïèòàíèÿ;
– ïîäêëþ÷èòü áëîê ïèòàíèÿ ê ñåòè 230 Â~ äâóìÿ ïðîâîäàìè ê ðàçú¸ìàì, óêàçàííûì
íà áëîêå ïèòàíèÿ:
EN
Before switching on, make sure that the input voltage of the power supply corresponds to
its operating range.
designed to operate from a DC voltage source of 12 V.
Basic information about the product
ATTENTION
Connect the LED strip with mechanical damage. Connect the LED strip directly to
the 230 V~ mains without a power supply. Connect the LED strip to the network, wound
on a bobbin.
Security measures
All installation and maintenance work must be carried out in a de-energized state by
specially trained personnel in compliance with the requirements of regulatory and technical
documentation in the field of electrical engineering.
Alternating voltage 230 V is life-threatening! During installation, do not expose
the tape to mechanical influences. It is not recommended to attach a tape with a
bending radius of less than 20 mm. When attaching the LED strip to conductive
surfaces, the tape must be isolated from contact with this surface.
PROHIBITED
LED strip 5050 series PRO trademark IEK (hereinafter referred to as the tape) is
2