manualshive.com logo in svg

IEI Technology WAFER-945GSELVDS2-N270-R10, User Manual

Share
Download
IEI Technology WAFER-945GSELVDS2-N270-R10 User Manual Download Page 111

 

 

WAFER-945GSELVDS2 

Page 99

5.5.1 Boot Settings Configuration 

Use the 

Boot Settings Configuration

 menu (BIOS Menu 16) to configure advanced 

system boot options. 

BIOS SETUP UTILITY 

Main 

Advanced 

PCIPNP 

Boot 

Security

Chipset

Exit 

 

 
Boot Settings Configuration 

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

 

Quick Boot 

[Enabled] 

Quiet Boot 

[Enabled] 

AddOn ROM Display Mode 

[Force BIOS] 

Bootup Num-Lock 

[On] 

 

 
Allows BIOS to skip 
certain tests while 
booting. This will 
decrease the time needed 
to boot the system. 
 
 

ÅÆ

 Select 

Screen 

↑

 

↓

 Select 

Item 

Enter Go to SubScreen 
F1 General 

Help 

F10 

Save and Exit 

ESC Exit 

v02.61 ©Copyright 1985-2006, American Megatrends, Inc. 

BIOS Menu 16: Boot Settings Configuration

 

ƒ

 

Quick Boot [Enabled] 

Use the 

Quick Boot

 BIOS option to make the computer speed up the boot process. 

Î

 

Disabled  

No POST procedures are skipped 

Î

 

Enabled D

EFAULT

 

Some POST procedures are skipped to decrease 

the system boot time 

ƒ

 

Quiet Boot [Disabled] 

Use the 

Quiet Boot

 BIOS option to select the screen display when the system boots. 

Î

 

Disabled D

EFAULT

 

Normal POST messages displayed 

Î

 

Enabled  

OEM Logo displayed instead of POST messages 

Summary of Contents for WAFER-945GSELVDS2-N270-R10













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands