manualshive.com logo in svg

IEI Technology tKINO-AL, User Manual

Share
Download
IEI Technology tKINO-AL User Manual Download Page 97

 

 

tKINO-AL SBC 

Page 83

5.3.10 SATA Configuration 

Use the 

SATA Configuration

 menu (

BIOS Menu 14

) to change and/or set the 

configuration of the SATA devices installed in the system. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

SATA Configuration 

 

SATA Mode Selection 

[AHCI]

 

 

SATA Port 0 

Not Present 

Hot Plug 

[Disabled] 

 

SATA Port 1 

Not Present 

Hot Plug 

[Disabled] 

 

 
Determines how SATA 
controller(s) operate. 
 
 
--------------------- 
 



: Select Screen 

 

: Select Item 

Enter 

Select 

F1 General 

Help 

F2 Previous 

Values 

F3 Optimized 
Defaults 
F4 Save 

 

ESC Exit 

Version 2.18.1263. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 14: SATA

 

Configuration

 

 

SATA Mode Selection [AHCI] 

Use the 

SATA Mode Selection

 option to configure SATA devices as AHCI devices. 

 

AHCI  

D

EFAULT

 

Configures SATA devices as AHCI device. 

 

Hot Plug [Disabled] 

Use the 

Hot Plug

 option to enable or disable the SATA device hot plug. 

 

Disabled D

EFAULT

 

Disable the SATA device hot plug capability. 

 

Enabled  

Enable the SATA device hot plug capability 

Summary of Contents for tKINO-AL









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands