manualshive.com logo in svg

IEI Technology tKINO-AL, User Manual

Share
Download
IEI Technology tKINO-AL User Manual Download Page 95

 

 

tKINO-AL SBC 

Page 81

5.3.8 USB Configuration 

Use the 

USB Configuration

 menu (

BIOS Menu 12

) to read USB configuration 

information and configure the USB settings. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

USB Configuration 
 
USB Devices: 
        1  Keyboard 

 
Legacy USB Support 

[Enabled] 

 
 
 

 
Enables Legacy USB 
support. AUTO option 
disables legacy support 
if no USB devices are 
connected. DISABLE 
option will keep USB 
devices available only 
for EFI applications. 
 
--------------------- 



: Select Screen 

 

: Select Item 

Enter 

Select 

F1 General 

Help 

F2 Previous 

Values 

F3 Optimized 
Defaults 
F4 Save 

 

ESC Exit 

Version 2.18.1263. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 12: USB Configuration

 

 

USB Devices 

The 

USB Devices Enabled

 field lists the USB devices that are enabled on the system 

 

Legacy USB Support [Enabled] 

Use the 

Legacy USB Support

 BIOS option to enable USB mouse and USB keyboard 

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard 

does not become available until a USB compatible operating system is fully booted with all 

USB drivers loaded. When this option is enabled, any attached USB mouse or USB 

keyboard can control the system even when there is no USB driver loaded onto the 

system.  

 

Summary of Contents for tKINO-AL









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands