IEI Technology TANK-870AI SERIES User Manual Download

Page: 92 / 137

TANK-870AI Embedded System

Page 78



Bits per second [115200]

Use the

Bits per second

option to specify the transmission speed of the serial port.



9600

The transmission speed is 9600



19200

The transmission speed is 19200



38400

The transmission speed is 38400



57600

The transmission speed is 57600



115200

EFAULT

The transmission speed is 115200



Data Bits [8]

Use the

Data Bits

option to specify the number of data bits.



Sets the data bits at 7.



EFAULT

Sets the data bits at 8.



Parity [None]

Use the

Parity

option to specify the parity bit that can be sent with the data bits for

detecting the transmission errors.



None

EFAULT

No parity bit is sent with the data bits.



Even

The parity bit is 0 if the number of ones in the data

bits is even.



Odd

The parity bit is 0 if the number of ones in the data

bits is odd.



Mark

The parity bit is always 1. This option does not

provide error detection.



Space

The parity bit is always 0. This option does not

provide error detection.

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands