IEI Technology SRM-KIT Series User Manual Download Page 26

Page: 26 / 77

SRM-KIT Series LCD Monitor

2.1 LCD Specifications

2.1.1 LCD Overview

The SRM-KIT series industrial monitors use the following LCD panels.

SRM-KIT121G

: MITSUBISHI AA121SN02 SVGA TFT LCD

SRM-KIT150G

: MITSUBISHI AA150XN08 XGA TFT LCD

Detailed specifications for the LCD screens are listed in the following sections.

2.1.2 SRM-KIT121G LCD Specifications

Table 2-1

lists the LCD specifications of the SRM-KIT121G.

Model

SRM-KIT121G

Size

12.1”

MFR/Model

MITSUBISHI AA121SN02

Resolution

SVGA (800 x 600)

Display Area (mm)

246.0 x 184.5

Pixel Pitch (mm)

0.3075 x 0.3075

Number of Colors

262K(6 bit/color), 16.7M(8 bit/color)

View Angle (H/V)

130 / 120

Brightness (cd/m

)

1000

Contrast Ratio

700:1

Response Time (ms)

: 10

: 30

Interface

LVDS (6 bit/8 bit)

Input Voltage (V)

3.3V

Backlight

4 CCFL

Page 12

Summary of Contents for SRM-KIT Series














































































Search results

Summary of Contents for SRM-KIT Series

Reviews:

Brands by name

Popular brands

IEI Technology SRM-KIT Series, User Manual

Search results

Summary of Contents for SRM-KIT Series

Reviews:

Brands by name

Popular brands