manualshive.com logo in svg

IEI Technology SPCIE-C2260-i2, User Manual, Page: 67 / 162

Share
Download
IEI Technology SPCIE-C2260-i2 User Manual Download Page 67

 

 

SPCIE-C2260-i2 PICMG 1.3 CPU Card 

Page 51 

4.2.1 Socket LGA1150 CPU Installation 

  WARNING: 

CPUs are expensive and sensitive components. When installing the 

CPU please be careful not to damage it in anyway. Make sure the CPU 

is installed properly and ensure the correct cooling kit is properly 

installed. 

DO NOT touch the pins at the bottom of the CPU. When handling the 

CPU, only hold it on the sides. 

To install the CPU, follow the steps below. 

Step 1: 

Disengage the load lever

 by pressing the lever down and slightly outward to 

clear the retention tab. Fully open the lever. See 

Figure 4-1

.

 

 

Figure 4-1: Disengage the CPU Socket Load Lever 

Step 2: 

Open the socket and remove the protective cover.

 The black protective 

cover can be removed by pulling up on the tab labeled "Remove". See 

Figure 4-2

. 

Summary of Contents for SPCIE-C2260-i2



































































































































































Reviews:

No comments