IEI Technology SPCIE-C2260-i2 Page 61 User Manual Download

Page: 61 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 45

3.3 External Peripheral Interface Connector Panel

The figure below shows the external peripheral interface connector (EPIC) panel. The

EPIC panel consists of the following:

Figure 3-28: External Peripheral Interface Connector

3.3.1 Ethernet Connectors

CN Label:

LAN1, LAN2

CN Type:

RJ-45

CN Location:

See

Figure 3-28

CN Pinouts:

See

Figure 3-29

and

Table 3-29

The SPCIE-C2260-i2 is equipped with two built-in RJ-45 Ethernet controllers. Each

controller can connect to the LAN through one RJ-45 LAN connector.

Pin

Description

Pin

Description

MDIA3-

MDIA2+

MDIA3+

MDIA1+

MDIA1-

MDIA0-

MDIA2-

MDIA0+

Table 3-29: LAN Pinouts

Figure 3-29: Ethernet Connector

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands