IEI Technology SPCIE-C2260-i2 Page 132 User Manual Download

Page: 132 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 116



Restore User Defaults

Use the

Restore User Defaults

option to restore the user defaults to all the setup options.

5.8 Server Mgmt

Use the

Server Mgmt

menu (

BIOS Menu 32

) to configure system event log and BMC

network parameters.

Main

Advanced

Chipset

Boot

Security Save & Exit Server Mgmt

BMC Self Test Status

> System Event Log
> BMC network configuration

Press <Enter> to change
the SEL event log
configuration.

---------------------



: Select Screen

↑

↓

: Select Item

Enter:  Select
+/-:  Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 32: Server Mgmt

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands