manualshive.com logo in svg

IEI Technology ROCKY-3786EV, User Manual, Page: 36 / 147

Share
Download
IEI Technology ROCKY-3786EV User Manual Download Page 36

 

 

Page 36 

 

ROCKY-3786EV CPU Card 

Page 36 

3.2 Internal Peripheral Connectors 

Internal peripheral connectors are found on the CPU card and are only accessible when 

the CPU board is outside of the chassis. This section has complete descriptions of all the 

internal, peripheral connectors on the ROCKY-3786EV CPU board. 

3.2.1 ATX Power Connector   

CN Label: 

CN21 

CN Type: 

20-pin header (2x10) 

CN Location: 

See Figure 3-2 

CN Pinouts: 

See Table 3-4 

The 

ROCKY-3786EV 

can work without backplane, while attaching external power to this 

ATX power connector. This connector supports the ATX power supply. 

PIN NO. 

DESCRIPTION 

PIN NO. 

DESCRIPTION 

11 3.3V 

1  3.3V 

12 -12V 

2  3.3V 

13 GND 

3  GND 

14 PSON# 

4  +5V 

15 GND 

5  GND 

16 GND 

6  +5V 

17 GND 

7  GND 

18 -5V 

8  Power 

good 

19 +5V 

9  +5VSB 

20 +5V 

10 +12V 

Table 3-4: ATX Power Connector Pinouts 

 

Summary of Contents for ROCKY-3786EV




















































































































































Reviews:

No comments