manualshive.com logo in svg

IEI Technology PM-BT series, User Manual

Share
Download
IEI Technology PM-BT series User Manual Download Page 79

 

 

PM-BT SBC 

Page 67 

5.3.8 CPU Configuration 

Use the 

CPU Configuration

 menu (

BIOS Menu 11

) to view detailed CPU specifications 

or enable the Intel Virtualization Technology. 

Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

CPU Information 
 
Intel(R) Celeron(R) CPU N2807 @ 1.58GHz 
CPU Signature 

30678 

Microcode Patch 

836 

Max CPU Speed 

1580 MHz 

Min CPU Speed 

500 MHz 

Processor Cores 

2 

Intel HT Technology 

Not Supported 

Intel VT-x Technology 

Supported 

 
L1 Data Cache 

24 kB x 2 

L1 Code Cache 

32 kB x 2 

L2 Cache 

1024 kB x 1 

L3 Cache 

Not Present 

64-bit 

Supported 

 

Intel Virtualization Technology  [Disabled] 
EIST   

[Enabled] 

CPU C state Report 

[Disabled] 

 

 
When enabled, a VMM can 
utilize the additional 
hardware capabilities 
provided by Vanderpool 
Technology. 
 
 
 
---------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter:  Select 
+/-:  Change  Opt. 
F1:  General Help 
F2:  Previous Values 
F3:  Optimized Defaults 
F4:  Save & Exit 
ESC: Exit 

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. 

BIOS Menu 11: CPU Configuration

 

 

Intel Virtualization Technology [Disabled] 

Use the 

Intel Virtualization Technology 

option to enable or disable virtualization on the 

system. When combined with third party software, Intel® Virtualization technology allows 

several OSs to run on the same system at the same time. 

 

Disabled 

D

EFAULT

 

Disables Intel Virtualization Technology. 

 

Enabled 

 

Enables Intel Virtualization Technology. 

Summary of Contents for PM-BT series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands