IEI Technology PICOe-9452 User Manual Download Page 139

Page: 139 / 250

PICOe-9452 Half-size CPU Card

Page 121



Legacy IDE Channels [PATA Pri, SATA Sec]



SATA Only

Only the SATA drives are enabled.



PATA Pri, SATA Sec

EFAULT

The IDE drives are enabled on the Primary

IDE channel. The SATA drives are enabled

on the Secondary IDE channel.



PATA Pri., PATA Sec

The IDE drives are enabled on the primary

and secondary IDE channels. SATA drives

are disabled.



IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the

status of the auto detected IDE devices. The following IDE devices are detected and are

shown in the

IDE Configuration

menu:



Primary IDE Master



Primary IDE Slave



Secondary IDE Master



Secondary IDE Slave

The

IDE Configuration

menu (

BIOS Menu 4

) allows changes to the configurations for the

IDE devices installed in the system. If an IDE device is detected, and one of the above

listed four BIOS configuration options are selected, the IDE configuration options shown in

Section 6.3.2.1

appear.

6.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

Summary of Contents for PICOe-9452



























































































































































































































































Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands

IEI Technology PICOe-9452, User Manual

Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands