IEI Technology PCISA-LX User Manual Download Page 94

Page: 94 / 214

Page 94

IEI® Technology, Corp

PCISA-LX CPU Card

BIOS Menu 1: AwardBIOS CMOS Setup Utility

NOTE:

The following sections will completely describe the menus

listed below and the configuration options available to users.

The following menu options are seen in

BIOS Menu 1

Standard CMOS Features

: Changes the basic system configuration.

Advanced BIOS Features

: Changes the advanced system settings.

Advanced Chipset Features

: Changes the chipset configuration features.

Integrated Peripherals

: Changes the settings for integrated peripherals.

Power Management Setup

: Configures power saving options.

PnP/PCI Configurations

: Changes the advanced PCI/PnP settings.

PC Health Status

: Monitors essential system parameters.

The following user configurable options are also available in

BIOS Menu 1

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands