IEI Technology PCISA-9652 User Manual Download Page 116

Page: 116 / 232

PCISA-9652 Half-Size CPU Card

Page 96

Center Subwoofer, connect to speakers. To install the audio kit, please refer to the steps

below:

Step 1:

Connect the audio kit cable.

The audio kit is shipped with a cable that

connects the audio kit to the PCISA-9652. Connect the cable to the connector

on the back of the audio kit. Make sure the pins are properly aligned (i.e. pin 1

connects to pin 1).

Step 2:

Locate the audio connector

. The location of the 10-pin audio connector is

shown in

Chapter 3

Step 3:

Align pin 1

. Align pin 1 on the on-board connector with pin 1 on the audio kit

cable connector. Pin 1 on the audio kit cable connector is indicated with a white

dot. See

Figure 5-17

Figure 5-17: 7.1 Channel Audio Kit

Step 4:

Mount the audio kit onto the chassis

. Once the audio kit is connected to the

PCISA-9652, secure the audio kit bracket to the system chassis.

Step 5:

Connect the audio devices

. Connect one speaker to the line-in audio jack, one

speaker to the line-out audio jack and a microphone to the mic-in audio jack.

Summary of Contents for PCISA-9652









































































































































































































































Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands

IEI Technology PCISA-9652, User Manual

Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands