IEI Technology Nova-lx User Manual Download

Page: 84 / 225

NOVA-LX 5.25” Motherboard

Page 64

25 R0

26 R1

26 R2

28 R3

29 R4

30 R5

31 R6

32 R7

33 GND

34 GND

35 CLK

36 VSYNC

37 LCD_EN 38 HSYNC

39 SCL

40 DISP_EN

Table 4-20: TFT LCD TTL Port Connector Pinouts

4.2.19 USB Connectors (Internal)

CN Label:

CN12 and CN13

CN Type:

8-pin header (2x4)

CN Location:

See Figure 4-20

CN Pinouts:

See Table 4-21

The 2x4 USB pin connectors each provide connectivity to two USB 1.1 or two USB 2.0

ports. Each USB connector can support two USB devices. Additional external USB ports

are found on the rear panel. The USB ports are used for I/O bus expansion.

Figure 4-20: USB Connector Pinout Locations

Summary of Contents for Nova-lx


































































































































































































































Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands

IEI Technology Nova-lx, User Manual

Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands