IEI Technology Nova-lx User Manual Download

Page: 78 / 225

NOVA-LX 5.25” Motherboard

Page 58

1 -5V

3 GND

5 -12V

Table 4-16: PC/104 Power Input Connector Pinouts

4.2.15 Serial Port Connectors (COM1, COM2)

CN Label:

CN30 and CN31

CN Type:

10-pin header (2x5)

CN Location:

See Figure 4-16

CN Pinouts:

See Table 4-17

The four 10-pin serial port connectors provide four additional RS-232 serial

communications channels. The four internal RS-232 serial port connectors can be

connected to external RS-232 serial port devices.

Figure 4-16: RS-232 COM Connector Pinout Locations

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

Data Carrier Direct (DCD)

Data Set Ready (DSR)

Summary of Contents for Nova-lx


































































































































































































































Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands

IEI Technology Nova-lx, User Manual

Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands