IEI Technology Nova-lx User Manual Download

Page: 106 / 225

NOVA-LX 5.25” Motherboard

Page 86

The PCI-104 Voltage Setup jumper location. is shown in Figure 5-11.

Figure 5-11: PCI-104 Voltage Setup Jumper Pinout Locations

5.6 Chassis Installation

5.6.1 Airflow

WARNING:

Airflow is critical to the cooling of the CPU and other onboard

components. The chassis in which the NOVA-LX must have air vents to

allow cool air to move into the system and hot air to move out.

The NOVA-LX must be installed in a chassis with ventilation holes on the sides allowing

airflow to travel through the heat sink surface. In a system with an individual power supply

unit, the cooling fan of a power supply can also help generate airflow through the board

surface.

Summary of Contents for Nova-lx


































































































































































































































Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands

IEI Technology Nova-lx, User Manual

Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands