IEI Technology NANO-QM871-i1 User Manual Download Page 97

Page: 97 / 156

NANO-QM871-i1 EPIC SBC

Page 84

5.3.5 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 7

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

SATA Controller(s)

[Enabled]

SATA Mode Selection

[IDE]

S_ATA1 Empty
S_ATA2 Empty
S_ATA3 Empty
S_ATA4 Empty
M-SATA1 Empty

Enable or disable SATA
Device.

---------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 7: SATA

Configuration

SATA Controller(s) [Enabled]

Use the

SATA Controller(s)

option to configure the SATA controller.

Enabled D

EFAULT

Enable SATA controller.

Disabled

Disable SATA controller.

SATA Mode Selection [IDE]

Use the

SATA Mode Selection

option to configure SATA devices.

IDE

EFAULT

Configures SATA devices as normal IDE device.

AHCI

Configures SATA devices as AHCI device.

RAID

Configures SATA devices as RAID device.

Summary of Contents for NANO-QM871-i1





























































































































































Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Brands by name

Popular brands

IEI Technology NANO-QM871-i1, User Manual

Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Brands by name

Popular brands