manualshive.com logo in svg

IEI Technology NANO-QM871-i1, User Manual

Share
Download
IEI Technology NANO-QM871-i1 User Manual Download Page 94

 

 

NANO-QM871-i1 EPIC SBC 

Page 81

5.3.3 Trusted Computing 

Use the 

Trusted Computing

 menu (

BIOS Menu 5

) to configure settings related to the 

Trusted Computing Group (TCG) Trusted Platform Module (TPM). 

Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

Configuration 
  

Security Device Support 

[Disable] 

 
Current Status Information 

 

  

NO Security Device Found 

 

 
Enables or Disables BIOS 
support for security 
device. O.S. will not 
show Security Device. 
TCG EFI protocol and 
INT1A interface will not 
be available. 
 
---------------------- 
 

: Select Screen 

↑

 

↓

: Select Item 

Enter: Select 
+/-:  Change  Opt. 
F1: General 

Help 

F2: Previous 

Values 

F3: Optimized 

Defaults

F4:  Save & Exit 
ESC: Exit 

Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc. 

BIOS Menu 5: Trusted Computing

 

  Security Device Support [Disable] 

Use the 

Security Device Support

 option to configure support for the TPM. 

 

Disable D

EFAULT

 

TPM support is disabled. 

 

Enable  

TPM support is enabled. 

Summary of Contents for NANO-QM871-i1





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands