manualshive.com logo in svg

IEI Technology NANO-QM871-i1, User Manual

Share
Download
IEI Technology NANO-QM871-i1 User Manual Download Page 78

 

 

NANO-QM871-i1 EPIC SBC 

Page 65

 

Figure 4-20: SATA Drive Cable Connection 

Step 3: 

Connect the cable to the SATA disk

. Connect the connector on the other end 

of the cable to the connector at the back of the SATA drive. See 

Figure 4-20

.

   

Step 4: 

To remove the SATA cable from the SATA connector, press the clip on the 

connector at the end of the cable.   

4.9.5 Single RS-232 Cable 

The single RS-232 cable consists of one serial port connector attached to a serial 

communications cable that is then attached to a D-sub 9 male connector. To install the 

single RS-232 cable, please follow the steps below. 

Step 1: 

Locate the connector

. The locations of the RS-232 connectors are shown in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Insert the connector into the serial port header. 

See 

Figure 4-21

. A key on the front of the cable connector ensures the 

connector can only be installed in one direction. 

Summary of Contents for NANO-QM871-i1





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands