manualshive.com logo in svg

IEI Technology KINO-QM770, User Manual

Share
Download
IEI Technology KINO-QM770 User Manual Download Page 88

 

 

KINO-QM770 Mini-ITX SBC

Page 72 

4.8.2 Single RS-232 Cable (w/o Bracket) 

The single RS-232 cable consists of one serial port connector attached to a serial 

communications cable that is then attached to a D-sub 9 male connector. To install the 

single RS-232 cable, please follow the steps below. 

Step 1: 

Locate the connector

. The location of the RS-232 connector is shown in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Insert the connector into the serial port pin header. 

See Figure 4-17. A key on the front of the cable connectors ensures the 

connector can only be installed in one direction. 

 

Figure 4-17: Single RS-232 Cable Installation 

Step 3: 

Secure the bracket

. The single RS-232 connector has two retention screws 

that must be secured to a chassis or bracket. 

Step 4: 

Connect the serial device

. Once the single RS-232 connector is connected to 

a chassis or bracket, a serial communications device can be connected to the 

system.

 

Step 0:

   

Summary of Contents for KINO-QM770

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands