manualshive.com logo in svg

IEI Technology KINO-QM770, User Manual

Share
Download
IEI Technology KINO-QM770 User Manual Download Page 87

 

 

KINO-QM770 Mini-ITX SBC 

Page 71

4.8 Internal Peripheral Device Connections 

This section outlines the installation of peripheral devices to the onboard connectors. 

4.8.1 SATA Drive Connection 

The KINO-QM770 is shipped with two SATA drive cable. To connect the SATA drive to the 

connector, please follow the steps below. 

Step 1: 

Locate the SATA connector and the SATA power connector

. The locations of 

the connectors are shown in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Insert the cable connector into the on-board SATA 

drive connector and the SATA power connector. See 

Figure 4-16

. 

 

Figure 4-16: SATA Drive Cable Connection 

Step 3: 

Connect the cable to the SATA disk

. Connect the connector on the other end 

of the cable to the connector at the back of the SATA drive. See 

Figure 4-16

.  

Step 4: 

To remove the SATA cable from the SATA connector, press the clip on the 

connector at the end of the cable.

 

Step 0:

 

Summary of Contents for KINO-QM770

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands