IEI Technology KINO-QM770 User Manual Download Page 109

Page: 109 / 208

KINO-QM770 Mini-ITX SBC

Page 93

USB Devices

The

USB Devices Enabled

field lists the USB devices that are enabled on the system

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.

Enabled D

EFAULT

Legacy USB support enabled

Disabled

Legacy USB support disabled

Auto

Legacy USB support disabled if no USB devices are

connected

5.3.10 F81866 Super IO Configuration

Use the

F81866

Super IO Configuration

menu (

BIOS Menu 12

) to set or change the

configurations for the FDD controllers, parallel ports and serial ports.

Advanced

F81866 Super IO Configuration

F81866 Super IO Chip

F81866

> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration

Set Parameters of Serial
Port 1 (COMA)

---------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

F1 General

Help

F2 Previous

Values

F3 Optimized
Defaults
F4 Save

ESC Exit

BIOS Menu 12: F81866 Super IO Configuration

Summary of Contents for KINO-QM770

















































































































































































































Search results

Summary of Contents for KINO-QM770

Reviews:

IEI Technology KINO-QM770, User Manual, Page: 109 / 208

Search results

Summary of Contents for KINO-QM770

Reviews: