IEI Technology KINO-KX Series User Manual Download Page 69

Page: 69 / 110

KINO-KX SBC

Page 57

5.3.2 ACPI Settings

The

ACPI Settings

menu (

BIOS Menu 4

) configures the Advanced Configuration and

Power Interface (ACPI) options.

Advanced

ACPI Settings

ACPI Sleep State

[S3 (Suspend to RAM]

Select the highest ACPI
sleep state the system
will enter when the
SUSPEND button is
pressed.

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 4: ACPI Settings



ACPI Sleep State [S3 (Suspend to RAM)]

Use the

ACPI Sleep State

option to specify the sleep state the system enters when it is

not being used.



S3 (Suspend to

RAM)

EFAULT

The caches are flushed and the CPU is powered

off. Power to the RAM is maintained. The

computer returns slower to a working state, but

more power is saved.

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands