IEI Technology KINO-KX Series User Manual Download Page 68

Page: 68 / 110

KINO-KX SBC

Page 56

5.3.1 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 3

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

Configuration

Security Device Support

[Disable]

NO Security Device Found

Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 3: Trusted Computing



Security Device Support [Disable]

Use the

Security Device Support

option to configure support for the security device.



Disable

EFAULT

Security device support is disabled.



Enable

Security device support is enabled.

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands