IEI Technology KINO-KX Series User Manual Download Page 19

Page: 19 / 110

KINO-KX SBC

Page 7

1.7 Technical Specifications

KINO-KX technical specifications are listed below.

Specification

KINO-KX

Form Factor

Mini-ITX

Processor

Zhaoxin KX-U6580 (8-core, 8 MB cache, 2.5 GHz, 70W)

Zhaoxin KX-U6780A (8-core, 8 MB cache, 2.7 GHz, 70W)

Chipset

Zhaoxin ZX-200

BIOS

AMI UEFI BIOS

Memory

Two 260-pin 2666 MHz DDR4 SDRAM SO-DIMM slots

(system max. 64 GB)

Graphics

C-960 Graphics Processing Unit with 2D/3D/video acceleration

Display Output

1 x VGA (up to 1920x1080@60Hz)

1 x DVI-I (up to 1920x1080@60Hz)

Ethernet

Dual Realtek RTL8111H PCIe GbE controller

Super IO

Fintek F81866

Audio

Realtek ALC888S HD audio codec

Watchdog Timer

Software programmable support 1~255 sec. system reset

I/O Interface

Audio Connector

3 x Audio jack (line-in, line-out and mic-in)

Ethernet

2 x RJ-45 GbE port

Serial Ports

2 x RS-232 by 10-pin (2x5) header

8 x RS-232 by two 40-pin (2x20) header

USB Ports

4 x USB 3.2 Gen 1 (5Gb/s) on rear I/O

10 x USB 2.0 on rear I/O

Front Panel

1 x Front panel connector by 10-pin (1x10) header for power LED, HDD

LED, power button and reset button

Fan

1 x CPU smart fan connector by 4-pin (1x4) wafer

1 x System smart fan connector by 4-pin (1x4) wafer

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands