IEI Technology KINO-690S1 User Manual Download Page 120

Page: 120 / 229

KINO-690S1 Mini-ITX Motherboard

Page 102

BIOS Menu 3: CPU Configuration

The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:

Revision

: Lists the CPU revision number

Cache L1

: Lists the CPU L1 cache size

Cache L2

: Lists the CPU L2 cache size

Speed:

Lists the CPU processing speed

Current FSB Multiplier

: Specifies how much the FSB is increased by

Maximum FSB Multiplier

: Specifies the maximum the FSB can be increased

Able to Change Freq

: Specifies the CPU frequency cannot be changed.

uCode Patch Level:

6.3.2 IDE Configuration

Use the

IDE Configuration

menu (

BIOS Menu 4

) to change and/or set the configuration

of the IDE devices installed in the system.

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 120 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: