IEI Technology KINO-690S1 User Manual Download Page 104

Page: 104 / 229

KINO-690S1 Mini-ITX Motherboard

Page 86

back of the SATA drive. See

Figure 5-11

Step 0:

Figure 5-11: SATA Power Drive Connection

5.7.5 USB Cable (Dual Port)

The KINO-690S1 is shipped with a dual port USB 2.0 cable. To connect the USB cable

connector, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the USB connectors are shown in

Chapter 3

WARNING:

If the USB pins are not properly aligned, the USB device can burn out.

Step 2:

Align the connectors

. The cable has two connectors. Correctly align pin 1on

each cable connector with pin 1 on the KINO-690S1 USB connector.

Step 3:

Insert the cable connectors

. Once the cable connectors are properly aligned

with the USB connectors on the KINO-690S1, connect the cable connectors to

the onboard connectors. See

Figure 5-12

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 104 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: