IEI Technology KINO-690S1 User Manual Download Page 102

Page: 102 / 229

KINO-690S1 Mini-ITX Motherboard

Page 84

side of the cable to one or two IDE devices. Make sure that pin 1 on the cable

corresponds to pin 1 on the connector

Step 0:

5.7.3 Dual RS-232 Cable Connection

The dual RS-232 cable consists of two connectors attached to two independent cables.

Each cable is then attached to a D-sub 9 male connector that is mounted onto a bracket.

To install the dual RS-232 cable, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the RS-232 connectors are shown in

Chapter 3

Step 2:

Insert the cable connectors

. Insert one connector into each serial port box

headers. See

Figure 5-9

. A key on the front of the cable connectors ensures the

connector can only be installed in one direction.

Figure 5-9: Dual RS-232 Cable Installation

Step 3:

Secure the bracket

. The dual RS-232 connector has two D-sub 9 male

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 102 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: