IEI Technology KINO-690S1 User Manual Download Page 101

Page: 101 / 229

KINO-690S1 Mini-ITX Motherboard

Page 83

HDTV Cable Set

LPT cable

VGA D-Sub cable with bracket

For more details about the items listed above, please refer to

Chapter 3

. Installation of the

accessories listed above are described in detail below.

5.7.2 ATA Flat Cable Connection

The ATA 66/100 flat cable connects to the KINO-690S1 to one or two IDE devices. To

connect an IDE HDD to the KINO-690S1 please follow the instructions below.

Step 1:

Locate the IDE connector

. The location/s of the IDE device connector/s is/are

shown in

Chapter 3

Step 2:

Insert the connector

. Connect the IDE cable connector to the onboard

connector. See

Figure 5-8

. A key on the front of the cable connector ensures it

can only be inserted in one direction.

Figure 5-8: IDE Cable Connection

Step 3:

Connect the cable to an IDE device

. Connect the two connectors on the other

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 101 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: