manualshive.com logo in svg

IEI Technology ITG-100-AL, User Manual

Share
Download
IEI Technology ITG-100-AL User Manual Download Page 70

 

 

ITG-100-AL Embedded System 

Page 58 

 

Legacy USB Support [Enabled] 

Use the 

Legacy USB Support

  BIOS option to enable USB mouse and USB keyboard 

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard 

does not become available until a USB compatible operating system is fully booted with all 

USB drivers loaded. When this option is enabled, any attached USB mouse or USB 

keyboard can control the system even when there is no USB driver loaded onto the 

system.   

 

Enabled 

D

EFAULT

 

Legacy USB support enabled 

 

Disabled 

 

Legacy USB support disabled 

5.3.8 iEi Feature 

Use the 

iEi Feature

 menu (

BIOS Menu 12

) to configure the iEi features. 

Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

iEi Feature 
 

Auto Recovery Function 

[Disabled] 

 

 
Auto Recovery Function 
Reboot and recover 
system automatically 
within 10 min, when OS 
crashes. Please install 
Auto Recovery API 
service before enabling 
this function. 
 
--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter 

Select 

+/-: Change Opt. 
F1:  General Help 
F2:  Previous Values 
F3:  Optimized Defaults 
F4:  Save & Exit 
ESC: Exit 

Version 2.18.1263. Copyright (C) 2018 American Megatrends, Inc. 

BIOS Menu 12: iEi Feature

 

 

Auto Recovery Function [Disabled] 

Use 

Auto Recovery Function

 option to enable or disable the auto recovery function. 

Summary of Contents for ITG-100-AL












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands