IEI Technology ISIGNAGER - 800WL-N270 Page 18 User Manual Download

Page: 18 / 67

iSignager-800WL-N270 Digital Signage Player

Page 10

1.9 Supported Formats

The iSignager-800WL-N270 supports many kinds of video, audio and graphic formats.

The supported formats are listed in

Table 1-3

. Detailed descriptions of each format can be

found in

Appendix A

NOTE:

The video in .mpe format can be run by iSignager-800WL-N270, but the video

length information will not be available.

iSignager-800WL-N270 Supported Formats

Video

MPEG-1 VCD format (1.15 Mbps CBR) [.mpg, .mpe, .mpeg, .dat, .m1v]

SD and HD MPEG-2 up to 15 Mbps [.mpg, .mpe, .mpeg, .m2v, .vob, .vro]

SD and HD MPEG-4 (OpenDivX, XviD, RMP4) [.avi, .divx, .mp4]

AVI audio codec: MP3, AC3, PCM, WMA

Audio

MPEG-1 Layer 1 (MP1) [.mp1, .mpa]

MPEG-1 Layer 2 (MP2) [.mp2]

MPEG-1 Layer 3 (MP3) [.mp3]

Microsoft

PCM Wave (WAV) [.wav]

Advanced Audio Coding (AAC, ADIF, ADTS) [.aac]

Apple MPEG-4 AAC Audio (M4A) [.m4a]

Microsoft

Windows

Media Audio version 1 and version 2 (WMA)

[.wma, .asf]

Microsoft

Windows

Media Audio Professional (WMA Pro) [.asf]

Graphic

16/24/32-bit color BMP, GIF, PNG, JPEG

Table 1-3: iSignager-800WL-N270 Supported Formats

Summary of Contents for ISIGNAGER - 800WL-N270




































































Search results

Summary of Contents for ISIGNAGER - 800WL-N270

Reviews:

Related manuals for ISIGNAGER - 800WL-N270

Brands by name

Popular brands

IEI Technology ISIGNAGER - 800WL-N270, User Manual

Search results

Summary of Contents for ISIGNAGER - 800WL-N270

Reviews:

Related manuals for ISIGNAGER - 800WL-N270

Brands by name

Popular brands