manualshive.com logo in svg

IEI Technology IMBA-H110, User Manual

Share
Download
IEI Technology IMBA-H110 User Manual Download Page 129

 

 

IMBA-H110 ATX Motherboard 

Page 115 

5.4.2.2 HD Audio Configuration 

Use the 

HD Audio Configuration 

menu (

BIOS Menu 26

) to configure  the PCH Azalia 

settings. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

 

Chipset 

 

 

 

 

HD Audio Configuration 

 

HD Audio  

[Auto] 

 

 

Control Detection of the 

HD-Audio device. 

Disable = HDA will be 

unconditionally 

disabled 

Enabled = HDA will be 

unconditionally enabled 

Auto = HDA will be 

enabled if present, 

disabled otherwise. 

---------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter:  Select 

+/-:  Change Opt. 

F1:  General Help 

F2:  Previous Values 

F3:   Optimized Defaults 

F4:  Save & Exit 

ESC: Exit 

 

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 26: HD Audio Configuration

 

 

HD Audio [Auto] 

Use the 

HD Audio 

option to enable or disable the High Definition Audio controller. 

 

Disabled   

The onboard High Definition Audio controller is disabled. 

 

Enabled   

The onboard High Definition Audio controller is enabled. 

 

Auto 

D

EFAULT

 

The onboard High Definition Audio controller 
automatically detected and enabled 

Summary of Contents for IMBA-H110

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands