manualshive.com logo in svg

IEI Technology IMBA-H110, User Manual

Share
Download
IEI Technology IMBA-H110 User Manual Download Page 117

 

 

IMBA-H110 ATX Motherboard 

Page 103 

5.3.10 USB Configuration 

Use the 

USB Configuration

  menu (

BIOS Menu 16

) to read USB configuration 

information and configure the USB settings. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

USB Configuration 

 

USB Controllers: 

        1 XHCI 

USB Devices: 

        1 Keyboard, 1 Hub 

 

Legacy USB Support 

[Enabled] 

 

 

 

Enables Legacy USB 

support. AUTO option 

disables legacy support 

if no USB devices are 

connected. DISABLE 

option will keep USB 

devices available only 

for EFI applications. 

--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter:  Select 

+/-:  Change Opt. 

F1:  General Help 

F2:  Previous Values 

F3:  Optimized Defaults 

F4:  Save & Exit 

ESC: Exit 

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 16: USB Configuration

 

 

Legacy USB Support [Enabled] 

Use the 

Legacy USB Support

  BIOS option to enable USB mouse and USB keyboard 

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard 
does not become available until a USB compatible operating system is fully booted with all 
USB drivers loaded. When this option is enabled, any attached USB mouse or USB 
keyboard can control the system even when there is no USB driver loaded onto the system.   

 

Enabled 

D

EFAULT

 

Legacy USB support enabled 

 

Disabled 

 

Legacy USB support disabled 

 

Auto 

 

Legacy USB support disabled if no USB devices are 
connected 

Summary of Contents for IMBA-H110

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands