IEI Technology IMBA-9454B User Manual Download Page 70

Page: 70 / 192

IMBA-9454B ATX Motherboard

Page 54

Figure 5-6: Securing the Heat sink to the PCB Board

Step 5:

Tighten the screws

. Use a screwdriver to tighten the four screws. Tighten each

nut a few turns at a time and do not over-tighten the screws.

Step 6:

Connect the fan cable

. Connect the cooling kit fan cable to the fan connector

on the IMBA-9454B. Carefully route the cable and avoid heat generating chips

and fan blades.

Step 0:

5.4 DIMM Installation

WARNING:

Using incorrectly specified DIMM may cause permanently damage the

IMBA-9454B. Please make sure the purchased DIMM complies with

the memory specifications of the IMBA-9454B. DIMM specifications

compliant with the IMBA-9454B are listed in Chapter 2.

To install a DIMM into a DIMM socket, please follow the steps below and refer to

Figure 5-7

Summary of Contents for IMBA-9454B

































































































































































































Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands

IEI Technology IMBA-9454B, User Manual

Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands