IEI Technology IMBA-9454B User Manual Download Page 62

Page: 62 / 192

IMBA-9454B ATX Motherboard

Page 46

5.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the

IMBA-9454B may result in permanent damage to the IMBA-9454B and

severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the IMBA-9454B. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the IMBA-9454B, or any other electrical component is handled, the

following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: When configuring the IMBA-9454B, place it on an

antic-static pad. This reduces the possibility of ESD damage.

Only handle the edges of the PCB

: When handling the PCB, hold it by its

edges.

5.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should

be read and understood before the IMBA-9454B is installed. All

installation notices pertaining to the installation of the IMBA-9454B

should be strictly adhered to. Failing to adhere to these precautions

may lead to severe damage of the IMBA-9454B and injury to the

person installing the motherboard.

Summary of Contents for IMBA-9454B

































































































































































































Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands

IEI Technology IMBA-9454B, User Manual

Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands