manualshive.com logo in svg

IEI Technology HYPER-BW, User Manual

Share
Download
IEI Technology HYPER-BW User Manual Download Page 72

 

 

HYPER-BW 

Page  61 

 

Disabled   

Disables the Intel Speed Step Technology. 

 

Enabled 

D

EFAULT

 

Enables the Intel Speed Step Technology. 

 

CPU C s tate Report [Dis abled] 

Use the 

CPU C

 

state Report 

option to enable or disable CPU C state report to OS. 

 

Disabled   

Disables CPU C state report to OS. 

 

Enabled 

D

EFAULT

 

Enables CPU C state report to OS. 

5.3.8

 

SATA Configuration 

Use the 

SATA  Configuration

  menu (

BIOS Menu 13

) to change and/or set the 

configuration of the SATA devices installed in the system. 

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

SATA Configuration 

 

 

SATA Mode Selection 

[AHCI] 

 

SATA1  

Not Present 

 

Hot Plug 

[Disabled] 

M_2_SATA1 

 

Not Present 

 

Hot Plug 

[Disabled] 

 

 

Determines how SATA 

controller(s) operate. 

 

--------------------- 

 



: Select Screen 

↑

 

↓

: Select Item 

Enter Select 

F1  General Help 

F2  Previous Values 

F3 

Optimized 

Defaults 

F4 

Save  

ESC  Exit 

Version 2.17.1249. Copyright (C) 2016 American Megatrends, Inc. 

BIOS Menu 13: IDE

 

Configuration

 

 

SATA Mode [ACHI Mode] 

Use the 

SATA Mode

 option to configure SATA devices as AHCI devices. 

 

ACHI Mode 

D

EFAULT

 

Configures SATA devices as AHCI device. 

Summary of Contents for HYPER-BW







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands