IEI Technology HTB-200-C236 User Manual Download Page 39 | Manualshive

Page: 39 / 113

background image

HTB-200-C236 Embedded System

Page 27

3.9 Power-On Procedure

3.9.1 Installation Checklist

WARNING:

Make sure a power supply with the correct input voltage is being fed into
the system. Incorrect voltages applied to the system may cause damage to
the internal electronic components and may also cause injury to the user.

To power on the embedded system please make sure of the following:



The top cover is installed



All peripheral devices (HDMI monitor, serial communications devices etc.) are

connected

3.9.2 Power-on Procedure

WARNING:

To avoid risk of electric shock, this equipment must only be connected
to supply mains with protective earth.

CAUTION:

Position the power cord so that people cannot step on it. Do not place
anything over the power cord. If the equipment is not used for a long
time, disconnect it from the power source to avoid damage by transient
over voltage.

«
...
37
38
39
40
41
...
»

Summary of Contents for HTB-200-C236


















































































































Reviews:

No comments

Related manuals for HTB-200-C236

Brand: Abicor Binzel Pages: 92

Brand: Bayer HealthCare Pages: 56

Brand: GFA Pages: 20

Brand: R.V.R. Elettronica Pages: 204

Weigh Scale Blender

Brand: MAGUIRE Pages: 141

Brand: BS Pages: 14

GQM22M5C2H101GB01 Series

Brand: Murata Pages: 25

Brand: R.V.R. Elettronica Pages: 38

Brand: S&C Pages: 20

Brand: Centa Pages: 52

Brand: Moeller Pages: 2

Brand: Moeller Pages: 4

Brand: ALFRA Pages: 32

Brand: Gecko Pages: 2

Brand: Rupes Pages: 36

SOMANET Circulo

Brand: SYNAPTICON Pages: 8

Brand: Pro-face Pages: 13

Brand: Oxford Instruments Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands